DIY - How to Make a Tyvek Flowform Kite

I wanted to make a new flow-form kite to replace the one that i lost while doing kite aerial photography (KAP). Also because i saw instructions and it looked a lot easier then the last Rokkaku Kite i made.

A flow-form kite doesn't require any supports. While reading about them i saw that some people made them out of Tyvek, which is a type of plastic houses are wrapped in to act as a vapor barrier.
Tyvek House Wrap, vapor barrier, tyvek
I checked Lowe's but all they had was their own type of house wrap and it only came in 160' lengths by 10' high and was $100.
 

Then on the way home from my sister's, Karrie and i stopped at Menard's. They had several different types and i decided on a soft, non-woven wrap that was only 3' high. It's the $35 one on the left.
Menards, non-woven housewrap, vapor barrier, tyvek
NovaWrap
NovaWrap, nova wrap, premium building wrap, vapor barrier, tyvek


It's actually really strong, i can barely rip it with my hands. close up view of tyvek, vapor barrier, house wrap

Here's what it looks like up close. close up view of tyvek, vapor barrier, house wrap
I looked at several patterns online and decided to go with this: The FF03A. It seemed simple, strong and stable. So i copied this drawing into AutoCAD and then traced the lines.
AutoCAD pattern for flowform kite, HP FF03A
AutoCAD allowed me to get actual dimensions of the material and make patterns.
AutoCAD pattern for flowform kite, HP FF03A, dimensions, printable, print
I ended up changing the dimensions. The original top was 115cm, i first changed it to 52".
computer pattern for kite, autocad, kite pattern, flowform
Then scaled it down to this size of 24" x 35" for the upper deck.
CAD pattern for kite, dimensions, pattern, print, top, sides
In my head 24" x 36" seemed a little small for a kite but when i printed out the full size patterns i realized how big it was. I might end up making the larger 36" x 52" kite but first i want to see how this smaller one fly's. It's not like i have a limited amount of Tyvek, it came in a 100' roll.



The upper and lower deck.
full size pattern for kite, tyvek, flowform kite, print
The sides and inner ribs.
full size pattern for kite, tyvek, flowform kite, print


Here's the top deck cut out. tyvek pattern, flowform kite, top deck, cut out
All of the pieces cut out.
all pieces cut out for kite, flowform, tyvek, cloth

I tested 4 different types of tape. After sticking them i made sure that i really pressed the tape into the Tyvek with the back side of a knife.

The tape in order:

  • Gorilla Glue duct tape
  • regular 3M duct tape
  • clear Tartan packaging tape
  • HD clear Duck tape
best tape to use with tyvek, house wrap, test, rip
The Gorilla Glue duct tape didn't stick well and was heavy. The HD clear Duck tape didn't stick well either. The 3M duct tape and Tartan packaging tape worked equally well. But since the Tartan tape was lighter i went with that. Also i think it was the cheapest, about $2.

Taping the fins.
tape kite fins, clear tape, tyvek, cloth, vertical fin
assemble kite, flowform, how to, tyvek

The hardest part was the final upper deck. It was difficult taping the insides all at once.
how to make a flowform kite from tyvek

Here it is with the rigging lines and tails attached.
tyvek kite made, asembled, ready to fly

I finally got to test the kite out. It flew ok. The main problem i had was that i didn't use a swivel clip to attach the line to the kite. That caused the kite to keep rotating clockwise until the bridal lines were completely twisted up.
flying my tyvek kite, make, made, tyvek, house wrap

Here's what the kite looked like as it flew at a low height.


But overall it flew surprisingly well. In high or low winds it was fairly steady. And when i was done it hadn't been damaged at all.
homemade kite, diy, tyvek, how to

Here it is higher up in the air.

Having built the kite, testing it and seeing how well it flew, i'm definitely not ready to tie my $300 Canon S95 camera to it to try and get some aerial pictures. I think we all remember how that ended up.

You have read the best review article categorized by AutoCAD / FF03A / Flow-form kite / house wrap / Lowe's / Menards / non-woven wrap / NovaWrap / pattern / Tape / Tyvek Kite and the title DIY - How to Make a Tyvek Flowform Kite. You can bookmark or spread this post by using this URL http://duiattorney-info.blogspot.com/2012/04/diy-how-to-make-tyvek-flowform-kite.html. Thank You!

Comments :

0 comments to “DIY - How to Make a Tyvek Flowform Kite”

Post a Comment

Powered by Blogger.

Blog Archive